TL431 + optocoupler Flybackfeedback calculation
Typical secondary-side TL431+optocoupler feedback for flyback: enumerate the divider from standard series, compute the LED limiting resistor, and derive the required primary current with CTR margin checks.
Key points
TL431 + optocoupler Flybackfeedback calculation: Typical secondary-side TL431+optocoupler feedback for flyback: enumerate the divider from standard series, compute the LED limiting resistor, and derive the required primary current with CTR margin checks. Formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. CCM flyback has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ. The compensation network (Type II, RC between REF and cathode) is tuned to the target crossover — this tool only computes DC operating-point resistors. In standby / no-load, if the required LED current drops below 1mA, add a resistor R≈(Vout−2.5V)/1mA from Vout to the TL431 cathode to keep it in its linear region.
Inputs
Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_minCalculation model (updates with parameters)
| [Divider] R1 (top) / R2 (bottom) | 5.23 kΩ / 1.37 kΩ | actual output 12.02 V | error 0.16% |
| [Divider] alternative 1 | 11.8 kΩ / 3.09 kΩ | Vout 12.02 V | error 0.19% |
| [Divider] alternative 2 | 16.5 kΩ / 4.32 kΩ | Vout 12.02 V | error 0.20% |
| [Divider] alternative 3 | 10.2 kΩ / 2.67 kΩ | Vout 12.03 V | error 0.22% |
| [Divider] sense current | 1.821 mA | ≥0.25mA (≥60× the ≤4µA REF bias) |
| [LED limiting] R_led | 2.8 kΩ | (Vled−Vf−Vka)/If, Vka = 2.5V; ideal 2.8 kΩ |
| [LED limiting] actual If | 3 mA | |
| [LED limiting] R_led dissipation | 25.2 mW | |
| [Primary] FB required current Ic | 470 µA | (Vpu−0.3V)/R_pu, with Vce_sat ≈ 0.3V |
| [Primary] derived If_min | 1.567 mA | Ic / CTR_min = Ic / 30% |
| [Primary] current margin | 1.9 × | If / If_min; recommend ≥1.5× |
| [TL431] cathode current | 3 mA | meets the 1mA minimum cathode current |
Engineering notes
- CCM flyback has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ. The compensation network (Type II, RC between REF and cathode) is tuned to the target crossover — this tool only computes DC operating-point resistors.
- In standby / no-load, if the required LED current drops below 1mA, add a resistor R≈(Vout−2.5V)/1mA from Vout to the TL431 cathode to keep it in its linear region.
- Too-small R_led raises LED current and standby loss; too-large lowers loop gain and worsens load regulation — pick a middle value with If=2–5mA.
FAQ
- What is TL431 + optocoupler Flybackfeedback calculation for?
- Typical secondary-side TL431+optocoupler feedback for flyback: enumerate the divider from standard series, compute the LED limiting resistor, and derive the required primary current with CTR margin checks.
- What is the formula for TL431 + optocoupler Flybackfeedback calculation?
- Core formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. The tool returns results instantly using this formula and the selected parameters.
- What engineering notes should I keep in mind when using TL431 + optocoupler Flybackfeedback calculation?
- CCM flyback has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ. The compensation network (Type II, RC between REF and cathode) is tuned to the target crossover — this tool only computes DC operating-point resistors. In standby / no-load, if the required LED current drops below 1mA, add a resistor R≈(Vout−2.5V)/1mA from Vout to the TL431 cathode to keep it in its linear region. Too-small R_led raises LED current and standby loss; too-large lower…
Embed this calculator on your site / blog / intranet
Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.