Skip to main content
DD-CAT IDE logoDD-CAT IDE

RCD / RDC Clamp Snubber Design

Favoriteused 1 times

RCD clamp for flyback leakage spikes: clamp resistor / capacitor / ultrafast diode values, loss, and drain stress.

Key points

RCD / RDC Clamp Snubber Design: RCD clamp for flyback leakage spikes: clamp resistor / capacitor / ultrafast diode values, loss, and drain stress. Formula: R = 2Vc(Vc−Vro)/(Llk·Ipk²·fsw) | C = Vc/(R·ΔV·fsw) | P = ½Llk·Ipk²·fsw·Vc/(Vc−Vro). Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. Raising Vclamp lowers loss (P ∝ Vc/(Vc−Vro)) but also raises drain stress — back-solve the limit from a 15–20% Vds margin. The clamp diode must be ultrafast (trr ≤ 35ns) with VRRM ≥ 1.2× drain peak; a slow diode re-injects energy during recovery, causing secondary ringing.

Inputs

R = 2Vc(Vc−Vro)/(Llk·Ipk²·fsw) | C = Vc/(R·ΔV·fsw) | P = ½Llk·Ipk²·fsw·Vc/(Vc−Vro)

Calculation model (updates with parameters)

VIN+PWMVclamp ≈ 200 VDR21.88 kΩC9.375 nFdrain peak ≈ 575 V(Vin(max) + Vclamp)

Bode plot (magnitude / phase, updates with parameters)

R∥C branch |Z|R only (no parallel C)-1001020304010 kHz100 kHz1 MHz10 MHzf (log axis)dB4.109 MHz12.3 dBΩ @ 4.109 MHzfsw · 261.2 ΩdBΩ relative to 1Ω; R-only clipped +40dB; fc = 775.9 Hz ≪ fsw; C regulates, R bleeds
Clamp resistor R21.88 kΩ
Clamp resistor dissipation1.828 W
Clamp capacitor C9.375 nF
actual ripple ΔV15 V
Drain peak voltage575 V
Vds margin ratio11.5 %
node ringing frequency (estimate)4.109 MHz
Clamp diodeVRRM ≥ 690 V
⚠ Vds margin only 11.5%: raising Vclamp is no longer viable; use a higher-voltage MOS or lower Vro.

Engineering notes

  • Raising Vclamp lowers loss (P ∝ Vc/(Vc−Vro)) but also raises drain stress — back-solve the limit from a 15–20% Vds margin.
  • The clamp diode must be ultrafast (trr ≤ 35ns) with VRRM ≥ 1.2× drain peak; a slow diode re-injects energy during recovery, causing secondary ringing.
  • The RCD only clamps the spike, not the ringing: hand residual ringing to an RC snubber (another tool in this group) or a secondary rectifier RC.

FAQ

What is RCD / RDC Clamp Snubber Design for?
RCD clamp for flyback leakage spikes: clamp resistor / capacitor / ultrafast diode values, loss, and drain stress.
What is the formula for RCD / RDC Clamp Snubber Design?
Core formula: R = 2Vc(Vc−Vro)/(Llk·Ipk²·fsw) | C = Vc/(R·ΔV·fsw) | P = ½Llk·Ipk²·fsw·Vc/(Vc−Vro). The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using RCD / RDC Clamp Snubber Design?
Raising Vclamp lowers loss (P ∝ Vc/(Vc−Vro)) but also raises drain stress — back-solve the limit from a 15–20% Vds margin. The clamp diode must be ultrafast (trr ≤ 35ns) with VRRM ≥ 1.2× drain peak; a slow diode re-injects energy during recovery, causing secondary ringing. The RCD only clamps the spike, not the ringing: hand residual ringing to an RC snubber (another tool in this group) or a secondary rectifier RC.
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.