Skip to main content
DD-CAT IDE logoDD-CAT IDE

Articles

News & Articles

Product news, technical insights, and industry practices — updated regularly.

Tech Insights

Learning Is Just Like Chasing Girls

Learning and chasing girls are the same thing: why you don’t want to learn, can’t learn, and can’t remember can each be punctured in one sentence by the Meng hexagram and logic. All science becomes as simple as a single “click.” Using side-by-side comparisons, it turns self-study into chasing girls—once you read it, you won’t forget.

Read more →

Tech Insights

Fairy-Tale Bias Circuits: From Resistive Divider to ΔV/R, Pinning Down the Amplifier's 'Standby Point'

An amplifier's performance comes down to where its 'standby point' is pinned: bias it wrong and a large signal clips; let it drift and a supply wobble throws everything off. This piece uses a barrel on a slope to explain what biasing is, then derives six generations of techniques step by step: the resistive divider → diode-connected device as a small resistor → current source as an infinite resistor → the self-biased four-transistor loop (and why it must end up 'dead or indeterminate') → the ΔV/R type with a source resistor → the V/R type for large currents. One consistent set of numbers (1.8 V / μCox=200 µA/V²) runs throughout, with supply-sensitivity comparison curves for the four structures, five common pitfalls, and a one-screen cheat sheet.

Read more →

Tech Insights

A Fairy-Tale Current Mirror: Three Generations of Gatekeepers on Mirror Lake, from a Single Transistor to the Wide-Swing Cascode (Formulas + Worked Examples + Applications)

A current mirror really comes down to one sentence: two transistors share one gate voltage, and the current is "copied" in proportion to their width-to-length ratios. Using my one-page sketch as material, I use the fairy tale of Mirror Lake's reflection to explain the trade-offs of three generations: the simple mirror (Iout/Iref = (W/L)₂/(W/L)₁, Rout = ro2 = 100 kΩ, but a 1 V change in Vout makes the current drift 5%), the cascode (Rout = ro2·gm4·ro4 = 20 MΩ, but Vout,min = VTH+2VDSAT = 0.9 V), and the wide-swing cascode (VB pushed down to VTH+2VDSAT, Vout,min = 2VDSAT = 0.4 V). Then I work a complete 1.8 V / 200 µA / ±1% sizing example (how to derive the Rout requirement, and why mismatch pushes the area from 10 µm² to 900 µm²), the two main error sources—channel-length modulation and mismatch—the "stiff only at low frequency" trap, and five real-world scenarios: op-amp biasing, current-steering DACs, bandgaps, sensor constant current, and current sensing.

Read more →

Tech Insights

Frequency Wavelength Calculator Notes: Parameter Selection and Common Mistakes

Notes from using a frequency wavelength calculator for antenna and PCB trace estimates, from the λ=c/f formula to dielectric wavelength correction, with a 2.45 GHz example and common unit and velocity factor mistakes.

Read more →

Tech Insights

A Fairy-Tale Guide to TVS Selection: How Low Should the Castle Gatekeeper Crouch?

TVS selection is never as simple as "a 24 V system just needs a 24 V part." This piece uses a black-box castle's gatekeeper to explain the whole thing: how to read six parameters on one I-V curve (VRWM, VBR, VC, R_dyn, IR, Cj), how to draw three red lines, how to convert an 8/20 µs waveform into joules and junction temperature, and why that easily ignored one millimeter of trace equals 30 volts. The focus is deep versus shallow snapback: the same part behaves as a self-resetting gatekeeper on a high-speed data line, but becomes a dead short welded in place on a power rail—with the mechanism (parasitic pnpn positive-feedback condition), a pros-and-cons comparison table, and a "usable / not usable" scenario checklist.

Read more →

Tech Insights

Femtoamp Measurement as a Fairy Tale: A Gatekeeper, a Thin Tube, and Reading 0.000000000000001 Amps as Millivolts

Femtoamp current measurement (photodiodes, ionization chambers, pH glass electrodes, chip leakage) looks mysterious, but it comes down to three things: a transimpedance stage turning current into voltage, an op amp with low enough bias current, and keeping that one square millimeter of PCB clean. This article uses the Fog Valley gatekeeper tale to explain virtual ground, feedback resistance, Johnson noise, and the Cf stability formula; then gives an Rf selection table (gain/noise/bandwidth/settling time from 1 MΩ to 1 TΩ), five op-amp gates, measured guard-ring and humidity numbers (10 pA across 1 mm of FR-4 at 60% RH), the 1 µV of thermal EMF equals 1 fA conversion, plus calibration and the full know-how of switching to the integration method below 100 aA.

Read more →