Skip to main content
DD-CAT IDE logoDD-CAT IDE

Online Tools

常用电子 / 电工 / 传感器 / Thermal Design / Mechanics / Thermodynamics / 电磁学Calculate工具

198电子 / 电工 / 嵌入式 / 传感器 / Thermal Design / Mechanics / Thermodynamics / 电磁学High频Calculate器,SVG 图示Calculate模型,填参数即时出结果:Resistance分压、DC-DC 反馈Resistance、TL431 反馈(Flyback / Forward)、PCB 阻抗 / 载流、CAN bits定时、CRC check、4-20mA、NTC / PT100、PLC 模拟量、散热器选型、Battery stringandCharge、Sallen-Key 滤波器、传输线延时、VSWR、motor选型、线路voltage drop、calorie诺效率……

Resistors & Passives

14 tools
Resistors & Passives

Resistor Voltage Divider

上臂 R1 接Input、下臂 R2 接地:既可按给定 R1/R2 算Output voltage,也可由Input量程and ADC 参数枚举StdResistance,给出Source impedance合适的采样最佳组合。

Vout = Vin × R2 / (R1 + R2) | ADC: R2/(R1+R2) = Vref(1−Margin)/Vin,maxused 84 times
Resistors & Passives

Series / Parallel Resistance

Equivalent resistance of series or parallel resistors, with k / M suffixes (e.g. 4.7k, 1M), up to 8 values.

series Rs = ΣRi | parallel 1/Rp = Σ(1/Ri)used 5 times
Resistors & Passives

Parallel Capacitor Calculator

Equivalent capacitance, total charge, and stored energy for parallel capacitors; supports pF / nF / µF / mF / F suffixes, up to 12 capacitors.

C_p = ΣCi | Q = C_p·V | E = ½·C_p·V²
Resistors & Passives

Wheatstone Bridge Calculator

Wheatstone bridge balance / output: solve the unknown arm from three resistors, or compute offset voltage, Thevenin resistance, and sensitivity from all four arms.

R1·Rx = R2·R3 | Vout = Vex·[R3/(R1+R3) − Rx/(R2+Rx)] | Rth = R1∥R3 + R2∥Rxused 1 times
Resistors & Passives

Capacitor Charge / Discharge Energy Calculator

Energy accounting for capacitor charge / discharge: source output, capacitor energy change, resistor / loop loss, charging efficiency, and average power at a repetition rate.

ΔQ = C·(V1−V0) | ΔE = ½C(V1²−V0²) | charge E_source = Vs·ΔQ | E_loss = E_source − ΔEused 2 times
Resistors & Passives

Resistor Color Code

Read resistance and tolerance from 4- or 5-band codes; the bands render live in the diagram.

R = (significant digits) × multiplier | 5-band adds one digit
Resistors & Passives

RC Filter / Cutoff Frequency

First order RC Low通 / High通滤波Calculate:由 R、C 求Cutoff frequency fc and任意频点衰减,或由 fc 反推 R / C,或按 fc 推荐标准 R、C 组合。

fc = 1 / (2πRC) | τ = RC | R = 1/(2π·fc·C) | C = 1/(2π·fc·R)used 6 times
Resistors & Passives

LC Resonance Frequency

LC 回路的谐振Frequencyand特性阻抗:由 L、C 求 f0,或由 f0 反推 L / C,或按 f0 推荐标准 L、C 组合,用于选频网络、Antenna匹配andsupply滤波。

f0 = 1 / (2π√(LC)) | Z0 = √(L/C) | L = 1/((2π·f0)²·C) | C = 1/((2π·f0)²·L)
Resistors & Passives

SMD Resistor Marking Calculator

Convert SMD resistor markings and resistance in both directions: 3-digit code (103 = 10 kΩ), 4-digit code (1002 = 10 kΩ), R decimal notation (4R7 = 4.7 Ω, R47 = 0.47 Ω) and EIA-96 precision code (01C = 10 kΩ), including all-zero jumpers.

3-digit AB×10^C | 4-digit ABC×10^D | R as decimal point | EIA-96: index (01–96) × multiplier letterused 25 times
Resistors & Passives

SMD Capacitor Code (104 = 100nF)

Two-way conversion between three- and four-digit EIA capacitor codes and capacitance, with code cross-reference, unit conversion and tolerance letters.

Code ABc = AB × 10^c pF (104 → 10×10⁴ = 100nF)used 7 times
Resistors & Passives

SMD Inductor Code (101 = 100µH)

Two-way conversion between three-digit inductor codes and inductance in µH, including the R decimal notation.

Code ABc = AB × 10^c µH (101 → 10×10¹ = 100µH)
Resistors & Passives

E-Series Value Picker (E24 / E96 / E192)

Given a target resistance, find the nearest E24/E96/E192 value and search series/parallel pairs that approach it — turn an odd value into something you can actually buy.

E96 has 96 steps per decade, adjacent ratio 10^(1/96) ≈ 1.0237used 15 times
Resistors & Passives

Resistor Color Bands (Value → Bands)

Given a value and tolerance, get the four- or five-band colour sequence with a drawn resistor — the fastest way to pick a part by eye.

4-band: digit · digit · multiplier · tolerance | 5-band: digit · digit · digit · multiplier · tolerance
Resistors & Passives

RC Charge / Discharge Time

First-order RC charge / discharge: compute the time constant, time to the target voltage, and the 63.2% / 95% / 99% and half-life points.

τ = R·C | charge t = −τ·ln(1 − Vt/Vs) | discharge t = −τ·ln(Vt/Vs)used 8 times