Skip to main content
DD-CAT IDE logoDD-CAT IDE

RC Snubber Design

Favoriteused 72 times

Ring damping for MOS / relay switching nodes: dual-frequency extraction of strays, with R/C values, loss, and an impedance Bode plot.

Key points

RC Snubber Design: Ring damping for MOS / relay switching nodes: dual-frequency extraction of strays, with R/C values, loss, and an impedance Bode plot. Formula: f_ring = 1/(2π√(LC)) | R = √(L/C) | Cs = 2~3Cp | P = Cs·ΔV²·fsw. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. Two-frequency method: ① measure ringing f₁ at the switching node; ② parallel a known small Cadd and measure f₂; ③ solve Lp / Cp — more reliable than guessing strays. Also applies to relay / thyristor contacts (often start with 100Ω + 100nF); for contacts, put R in series before C to limit inrush.

Inputs

f_ring = 1/(2π√(LC)) | R = √(L/C) | Cs = 2~3Cp | P = Cs·ΔV²·fsw

Calculation model (updates with parameters)

VIN+PWMR10 ΩCs2.5 nFf_ring ≈ 15.92 MHz|Z₀ = 10 ΩThe RC series branch sits across the switch D-S; ringing energy is dissipated in R

Bode plot (magnitude / phase, updates with parameters)

With RC snubber |Z|No snubber (LC resonance)-20-10010203040-90°-45°0°45°90°1 MHz10 MHz100 MHz1 GHzf (log axis)dBphase15.92 MHz-22° @ 15.92 MHzDamped peak 22.0 dBΩImpedance spectrum in dBΩ (relative to 1Ω); ideal LC peak clipped at +40dB; damped peak ≈ 1.1·Z₀
Ringing frequency f_ring15.92 MHz
Stray capacitance Cp1 nF
Stray inductance L100 nH
characteristic impedance Z₀ = √(L/C)10 Ω
Recommended snubber resistor R10 Ω
Recommended snubber capacitor Cs2 nF ~ 3 nF
Snubber branch corner frequency6.366 MHz
Snubber resistor dissipation1.625 W
⚠ Snubber resistor dissipation 1.625 W High: choose 1206 or larger with 2× margin.

Engineering notes

  • Two-frequency method: ① measure ringing f₁ at the switching node; ② parallel a known small Cadd and measure f₂; ③ solve Lp / Cp — more reliable than guessing strays.
  • Also applies to relay / thyristor contacts (often start with 100Ω + 100nF); for contacts, put R in series before C to limit inrush.
  • The RCD clamp (another tool here) handles flyback leakage spikes; the RC snubber handles ringing and dv/dt — the two can coexist.

FAQ

What is RC Snubber Design for?
Ring damping for MOS / relay switching nodes: dual-frequency extraction of strays, with R/C values, loss, and an impedance Bode plot.
What is the formula for RC Snubber Design?
Core formula: f_ring = 1/(2π√(LC)) | R = √(L/C) | Cs = 2~3Cp | P = Cs·ΔV²·fsw. The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using RC Snubber Design?
Two-frequency method: ① measure ringing f₁ at the switching node; ② parallel a known small Cadd and measure f₂; ③ solve Lp / Cp — more reliable than guessing strays. Also applies to relay / thyristor contacts (often start with 100Ω + 100nF); for contacts, put R in series before C to limit inrush. The RCD clamp (another tool here) handles flyback leakage spikes; the RC snubber handles ringing and dv/dt — the two can coexist.
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.