WiFi/BT PCB Antenna Design
2.4GHz PCB antenna: λ/4 inverted-F (IFA) arm length or half-wave patch W/L/feed inset, with 50Ω feed width and clearance notes.
Key points
WiFi/BT PCB Antenna Design: 2.4GHz PCB antenna: λ/4 inverted-F (IFA) arm length or half-wave patch W/L/feed inset, with 50Ω feed width and clearance notes. Formula: λ/4 arm = c/(4f·√εeff)|patch W = c/(2f)·√(2/(εr+1)), L = c/(2f·√εeff) − 2ΔL. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. PCB λ/4 antennas vary a lot: prototype with ±2mm around the initial arm length, measure resonance with a VNA and trim the tip; place the IFA at the board edge with the arm facing out. Keep ≥3h clearance (no copper or traces) below and around the arm; keep batteries / metal / shields ≥10mm away, or it detunes and efficiency plummets.
Inputs
λ/4 arm = c/(4f·√εeff)|patch W = c/(2f)·√(2/(εr+1)), L = c/(2f·√εeff) − 2ΔLCalculation model (updates with parameters)
| Free-space wavelength λ0 | 122.4 mm | 2.45 GHz |
| in-dielectric wavelength λg | 88.8 mm | εeff(arm) = 1.90 |
| Radiating arm length (λ/4) | 22.2 mm | Free-space average model; trim within ±2mm on a sample using a VNA |
| Ground stub and coupling gap | g ≈ 1~2 mm | The ground stub extends from the GND edge; trim its length on a sample |
| 50Ω feed width | 3.02 mm | 1.6mm board · 1oz copper |
Engineering notes
- PCB λ/4 antennas vary a lot: prototype with ±2mm around the initial arm length, measure resonance with a VNA and trim the tip; place the IFA at the board edge with the arm facing out.
- Keep ≥3h clearance (no copper or traces) below and around the arm; keep batteries / metal / shields ≥10mm away, or it detunes and efficiency plummets.
- BT and 2.4G WiFi can share one 2.45GHz antenna; 5G WiFi needs a separate 5.5GHz antenna or a dual-band design.
- FR-4 loss is significant at 5.8GHz (tanδ≈0.02); consider Rogers or an external antenna at high bands; OTA/conducted tests are required before production.
FAQ
- What is WiFi/BT PCB Antenna Design for?
- 2.4GHz PCB antenna: λ/4 inverted-F (IFA) arm length or half-wave patch W/L/feed inset, with 50Ω feed width and clearance notes.
- What is the formula for WiFi/BT PCB Antenna Design?
- Core formula: λ/4 arm = c/(4f·√εeff)|patch W = c/(2f)·√(2/(εr+1)), L = c/(2f·√εeff) − 2ΔL. The tool returns results instantly using this formula and the selected parameters.
- What engineering notes should I keep in mind when using WiFi/BT PCB Antenna Design?
- PCB λ/4 antennas vary a lot: prototype with ±2mm around the initial arm length, measure resonance with a VNA and trim the tip; place the IFA at the board edge with the arm facing out. Keep ≥3h clearance (no copper or traces) below and around the arm; keep batteries / metal / shields ≥10mm away, or it detunes and efficiency plummets. BT and 2.4G WiFi can share one 2.45GHz antenna; 5G WiFi needs a separate 5.5GHz antenna or a dual-band design. FR-4 loss is significant at 5.8GH…
Embed this calculator on your site / blog / intranet
Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.