Skip to main content
DD-CAT IDE logoDD-CAT IDE

Resistor Voltage Divider

Favoriteused 84 times

上臂 R1 接Input、下臂 R2 接地:既可按给定 R1/R2 算Output voltage,也可由Input量程and ADC 参数枚举StdResistance,给出Source impedance合适的采样最佳组合。

Key points

Resistor Voltage Divider: 上臂 R1 接Input、下臂 R2 接地:既可按给定 R1/R2 算Output voltage,也可由Input量程and ADC 参数枚举StdResistance,给出Source impedance合适的采样最佳组合。 Formula: Vout = Vin × R2 / (R1 + R2) | ADC: R2/(R1+R2) = Vref(1−Margin)/Vin,max. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. The standard divider uses the no-load formula; the next stage’s input impedance must be ≥ 10×R2, otherwise recalculate as a parallel combination. ADC mode: divider ratio = Vref×(1−headroom) / Vin,max, then enumerate R1/R2 from the standard series. The constraint is ADC-side source impedance R1∥R2 ≤ the datasheet limit, balancing sample/hold charging against dissipation.

Inputs

Vout = Vin × R2 / (R1 + R2) | ADC: R2/(R1+R2) = Vref(1−Margin)/Vin,max

Calculation model (updates with parameters)

Vin5 VR19.1 kΩR21 kΩVout495 mV
Output voltage Vout495 mV
[Rounded] R1 / R29.1 kΩ / 1 kΩ
[Rounded] Vout deviation-0.99%
Divider current I495 µA
R1 dissipation2.23 mW
R2 dissipation245.1 µW

Engineering notes

  • The standard divider uses the no-load formula; the next stage’s input impedance must be ≥ 10×R2, otherwise recalculate as a parallel combination.
  • ADC mode: divider ratio = Vref×(1−headroom) / Vin,max, then enumerate R1/R2 from the standard series. The constraint is ADC-side source impedance R1∥R2 ≤ the datasheet limit, balancing sample/hold charging against dissipation.
  • Source impedance is R1∥R2 (Thevenin equivalent): a SAR ADC charges its internal sample capacitor at each conversion, and too high a source impedance causes low readings and more crosstalk — lower the sample rate or add a small capacitor at the ADC pin if needed.
  • Resistor tolerance (e.g. ±1%) turns directly into ratio error; for high accuracy use E96 and tight-tolerance resistors, and calibrate the gain with a two-point software calibration.
  • The error analysis adds worst cases linearly (resistor tolerance + reference tolerance + ADC offset/gain/INL) and gives an RSS typical value; resistors of the same type and batch partially cancel their tempco, while wiring and buffer offset must be added separately.

FAQ

What is Resistor Voltage Divider for?
上臂 R1 接Input、下臂 R2 接地:既可按给定 R1/R2 算Output voltage,也可由Input量程and ADC 参数枚举StdResistance,给出Source impedance合适的采样最佳组合。
What is the formula for Resistor Voltage Divider?
Core formula: Vout = Vin × R2 / (R1 + R2) | ADC: R2/(R1+R2) = Vref(1−Margin)/Vin,max. The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using Resistor Voltage Divider?
The standard divider uses the no-load formula; the next stage’s input impedance must be ≥ 10×R2, otherwise recalculate as a parallel combination. ADC mode: divider ratio = Vref×(1−headroom) / Vin,max, then enumerate R1/R2 from the standard series. The constraint is ADC-side source impedance R1∥R2 ≤ the datasheet limit, balancing sample/hold charging against dissipation. Source impedance is R1∥R2 (Thevenin equivalent): a SAR ADC charges its internal sample capacitor at each c…
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.